Manufacturing

Home / Manufacturing / Industrial Valves

Industrial Valves


We proffer industrial valves in a broad selection of the material of the construction like the Cast Iron, the Cast Steel, the Stainless Steel of 304/CF8, 316/CF8M, Alloy-20.

1. Ball Valve Series:

We offer complete series of Ball control valves such as Single Piece, Two Piece & Three Piece Ball Valves with a very broad range for proportionally controlled application. The rugged design of the valve assures reliable performance under extremes of operating conditions, pipeline stresses, hydraulic & thermal shocks. A wide selection of construction material such as i.e. CAST IRON, CAST STEEL, STAINLESS STEEL 304/CF8, 316/CF8M, ALLOY-20 is available.

2. Gate Valve:

N&T Gate Valves are Bolted Bonnet, Rising Spindle, and Outside Screw & Yoke Type construction. These Gate Valve are available with solid wedge, Flexible wedge, Split wedge, and Parallel Sliding wedge designs offer maximum flexib

3. Gate Valve:

N&T Gate Valves are Bolted Bonnet, Rising Spindle, and Outside Screw & Yoke Type construction. These Gate Valve are available with solid wedge, Flexible wedge, Split wedge, and Parallel Sliding wedge designs offer maximum flexibility and option available to customer for their suitable selection. Gate Valve having Deep stuffing box, which provides assure tightness and maximum packing life. Separate properly machined and lapped back seat facilities are provided for replacement of gland packing when valve is online & under pressure

We offer extra-long, extended bonnet Gate valve for special services. Antifriction thrust bearing is provided in yoke sleeve for higher sizes and classes.

4. Check Valve Series:

Vertical Swing Check Valve

N&T Check Valves are Bolted cover design up to 300# and above pressure seal design. These valves are suitable for vertical as well horizontal lines.

Application: Oil, Gas, Water, Refining, Power and Chemical etc. i.e. where the prevention of flow reversal is mandatory.

Horizontal Swing Check valve

N&T Check Valves are Bolted cover design up to 300# and above pressure seal design. These valves are suitable for vertical as well horizontal lines.

Application: Oil, Gas, Water, Refining, Power and Chemical etc. i.e. where the prevention of flow reversal is mandatory.

Wafer Check Valve

Wafer Design Plate Type Check Valve has short face-to-face dimensions and low weight allows a simple space saving installation between the companion flanges. The valves are suitable to mounting between weld neck or slip on type companion flanges of different standards.

They are specially developed for applications where a low-pressure loss is essential. Opening and closing of the valve will take place at an extremely low pressure difference over the valve disc. The eccentric disc shaft combination with the disc seat guarantees a positive shut off returning media. Wafer check valve are becoming the preferred type of check valve for most applications, due to their compact design and relatively low cost.

Slim Check Valve

N&T Check Valves are Bolted cover design up to 300# and above pressure seal design. These valves are suitable for vertical as well horizontal lines.

5. Needle Valve:

N&T series of needle valves are available in bar stock round & square body with screwed connections BSPT, BSPT, Socket weld, Butt Weld & Special demand flange End Connection. Needle valves are similar in design and operation to the globe valve. Instead of a disk, a steady one piece needle stem with a long-tapered point at the end of the valve stem. The long taper of the valve element permits a much smaller seating surface area than that of the globe valve; the needle valve is more suitable as a throttle valve especially air & pressure. Normally the material of needle valve bodies and its various parts SS 304, SS 316, SS 304L, SS 316L etc. depending on the application. Needle valves are used to control flow into delicate gauges, which might be damaged by sudden surges of fluid under pressure.

 

6. Strainer

Y Type Strainer

We are manufacturers of wide range of Industrial Strainers. With Bolted cover design, the “Y” type strainer automatically removes solids & foreign particles from flowing liquids, air, steam or gases by the use of perforated sheet or wire mesh straining element. High area of “Y” type strainer has low pressure drop due to higher flow area through screen. The strainer improves clearance in the medium, and prolongs the life of valves, protects expensive pumps, meters and other costly equipment. These strainers are available in wide range of body material construction, pressure ranges and screen sizes for various suitable applications.

“Y” type strainers are easy to install in either horizontal or vertical position. During both direction installations, the screening element must be on the “down side” of the strainer body, so the entrapped material can be properly collected in it. These strainers also available with drain plug which can be replaced with ball valve of gate or plug valve for frequent blow off.

We offer strainers in polypropylene too.

Send us an inquiry to get a price quote or know more.